空氣增壓泵 |氣體增壓泵 |氣液增壓泵 |爆破試驗臺 歡迎來到污视频带污疼痛的叫声官方網站!
全國咨詢熱線:188-6686-9103

專注于氣體增壓泵、空氣增壓泵提高生產效率,降低人工成本

熱門關鍵詞: 空氣增壓泵 氣體增壓泵 氣液增壓泵污视频带污疼痛的叫声

其他頁面banner圖
當前位置:首頁 > 新聞中心 > 行業新聞

高壓空氣增壓泵怎樣做好安裝

發布者:system 發布日期:2018-12-17

1.高壓空氣增壓泵的安裝

Installation of 1. high pressure air booster pump

污视频带污疼痛的叫声空氣增壓閥標配有兩個開槽安裝支架,增壓閥可以安裝在任意位置,推薦位置為垂直方向,每臺售出增壓閥都會附帶圖紙,標注所需的各種尺寸。

The air booster valve is equipped with two slotted mounting brackets, the booster valve can be installed at any position, the recommended position is vertical, each booster valve will be attached with the drawings, marking all the required sizes.

2.預增氣源連接

2. yejiyuzeng source connection

高壓空氣增壓泵泵體上都標注“進口”,且圖紙上都標有端口尺寸及型號。預增氣體一定要純凈,氣體介質若有雜志可能會損壞高壓元件,導致增壓閥運行故障,所以建議大家在增壓閥進氣口安裝過濾裝置。

High pressure air booster pump body is marked "import", and the drawings are marked with port size and type. The pre - added gas must be pure. If there is a magazine in the gas medium that may damage the high pressure components and cause the operation failure of the pressurized valve, it is suggested that you install the filter in the air inlet of the pressurized valve.

3.氣源的連接

污视频带污疼痛的叫声Connection of 3. gas sources

供氣回路的安裝時過濾/調壓閥需盡量開進增壓閥。進氣口端口為G1/4”,閥體上標注為”驅動氣口“,管徑為1/2”,如果管徑較小,增壓閥就不可以以最大流量運行。過濾調壓需按照名稱順序鏈接,靠近增壓閥。

When the gas supply circuit is installed, the filter / pressure regulating valve should be pushed into the booster valve as far as possible. The inlet port is G1/4 "and the valve body is marked as" driving air inlet ". The pipe diameter is 1/2". If the pipe diameter is small, the pressurized valve can not run with the maximum flow. Filtering and voltage regulation should be linked in name sequence, close to the booster valve.

4.消聲器

4. muffler

消聲器的使用時用來降低增壓閥運行時的噪音,保證運行環境的安靜。排氣口端口為G1/2”,標記為“出氣口”。

The muffler is used to reduce the noise of the booster valve and ensure the quietness of the running environment. The port of the exhaust port is G1/2, marked as "air outlet".

5.高壓氣體出口的連接

5. connection of high pressure gas outlet

在增壓閥的配圖上標有端口尺寸及型號,增壓閥閥體上標注為“出口”,此為高壓出口,所以連接時需要特別謹慎小心,連接件需要大于最大輸出壓力。

污视频带污疼痛的叫声The size and model of the turbocharger valve are marked with the size and size of the port, and the valve body is marked as "exit". This is the high pressure outlet, so the connection needs to be careful and careful. The connector needs to be greater than the maximum output pressure.

污视频带污疼痛的叫声6.高壓空氣增壓泵的啟動

污视频带污疼痛的叫声The start of 6. high pressure air booster pump

⑴在打開增壓閥的進氣開關之前,使用調節減壓閥將氣壓調到“0”PSI

In the switch before the intake pressure valve, regulating valve pressure will be transferred to the "0" PSI

污视频带污疼痛的叫声⑵確保所有的連接口及所有元件及安裝。

The connection port and ensure all all the components and installation.

⑶將減壓閥緩慢調節至增壓閥開始啟動,正常情況下增壓閥在15-20PSI壓力下氣動。

The valve will slowly adjust to the pressure valve is started, under normal circumstances, the pressure valve under the pressure of 15-20PSI pneumatic.

⑷完成1到3步驟后,調節泵的供氣氣壓直達到系統所需輸出壓力為止。

The completion of the 1 to 3 steps, gas pressure regulating pump system to direct the desired output pressure.


污视频带污疼痛的叫声
全國咨詢熱線:188-6686-9103

公司電話:0531-69951198

污视频带污疼痛的叫声公司傳真:0531-69951198

污视频带污疼痛的叫声公司QQ:7786252626

污视频带污疼痛的叫声公司地址:濟南市歷城區西周南路9號